Closed. This question is not about programming or software development. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 8 days ago.
Improve this question
Using ESXi 6.7 as the main VM host. Created a VM with the necessary hard disk, CPU and RAM requirements.
Network interface is configured as VMXNET3. However, when the installer gets to the network configuration step, it fails to get an IP address. If I choose the E1000, same result.
What do I need to do for the DHCP process to complete?
Other VM's on the same host are able to acquire IP address without any problems.
Related
Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 2 years ago.
Improve this question
I have to connect to company VPN to access the internal applications and to do the testing. Once I connect to VPN the internet gets disconnected, so I did the following setup.
I installed windows 10 in the Virtual Box (VM) and connects to the company VPN in the VM. Now I have the Physical Machine that is connected to Internet and the VM that is connected to VPN.
I want to forward all requests from POSTMAN in the Physical Machine to the Virtual Machine.
Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 5 years ago.
Improve this question
Here I am exploring the security features, and when I enter "firewall-cmd --panic-on" to the CLI, the system just hangs idle.
Centos 7
Kernel 3.10
I think this is not supposed to happen, b/c as I read the documentation, I see I should be able to firewall-cmd --panic-off, but I cannot even ssh through another terminal unless I restart the server.
Is the system corrupt?
Is there a bug with "firewall-cmd --panic-on"?
How can I figure out the source of the problem?
--panic-on
Enable panic mode. All incoming and outgoing packets are dropped, active connections will expire. Enable this only if there are
serious problems with your network environment. For example if the
machine is getting hacked in.
As this switch drops all incoming connections and kills established active connections, so you can not issue --panic-off using ssh. You have to run firewall-cmd --panic-off using console access. running firewall-cmd --panic-on will apply configuration in runtime level so by simply restarting the server you can access ssh session. never run firewall-cmd --panic-on --permanent you can verify panic status by running firewall-cmd --query-panic
Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 5 years ago.
Improve this question
I need to connect to my virtual box running on my local machine to transfer files from my local system to VM by using WinSCP.
How do I find the IP address?
When I go to the settings and network tab, there I find something related to IP, but when I use that, it says cannot find or invalid.
Login to virtual machine use below command to check ip address. (anyone will work)
ifconfig
ip addr show
If you used NAT for your virtual machine settings(your machine ip will be 10.0.2.15), then you have to use port forwarding to connect to machine. IP address will be 127.0.0.1
If you used bridged networking/Host only networking, then you will have separate Ip address. Use that IP address to connect virtual machine
Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 9 years ago.
Improve this question
I have two virtual machine on vmware player both, each have a NIC card. I want to direct connect VM1's NIC to VM2's NIC, not bridge, not NAT, not Host-only, just direct connect like connect through wire.
Is is possible? How can I do this? Thanks!
Use an undefined "Custom" virtual network. Address one VM as 192.168.10.1 and the other as 192.168.10.2. With no gateway or NAT it's essentially a two-port hub. I believe that's as close as you'll get to a crossover.
Closed. This question does not meet Stack Overflow guidelines. It is not currently accepting answers.
This question does not appear to be about a specific programming problem, a software algorithm, or software tools primarily used by programmers. If you believe the question would be on-topic on another Stack Exchange site, you can leave a comment to explain where the question may be able to be answered.
Closed 2 years ago.
Improve this question
I'm working on Linux ubuntu, so to test the page on IE6/7/8 etc I run a virtual machine using virtual box; I also need to see how my localhost looks on IE in a windows virtual box environment).
but I dont want to re install my poroject on, lamp on the vm
In my real machine, I open the website simply using the URL local, how do I address this localhost from my Linux ubuntu to the virtual machine?
Right now my workaround is to use the IP address. Any better ideas?
In the default network configuration (NAT) for VirtualBox you can accesss the host machine with the IP 10.0.2.2, so in the browser you would use that instead of localhost. (I can't find this in the official documentation though?)