I have connected OpenVPN with Google Cloud VPC by following youtube video
https://www.youtube.com/watch?v=avYcoMKaXRc
Right now I am in Singapore and wants to connect Google Cloud India, setup is perfect but after successful connection if I try to open any website, on-one is opening, like there is no internet connection.
Can any one help me what is the issue? thanks
To monitor and solve common issues with Cloud VPN, follow the GCP Cloud VPN troubleshooting guide and OpenVPN troubleshooting.
Even the VPN gateways are configured correctly, there could be issue in the peer network between the hosts and the gateway, or with the network between the peer gateway and the Cloud VPN gateway.
Check for the Cloud VPN logs in Stackdriver Logging and verify these steps.
Verify connectivity between your host and Google Cloud VMs;
Are you able to reach peer VPN gateway from your host.
Verify that traffic is flowing between the two VPN gateways in both directions. In the VPN logs, check for reported incoming messages from the other VPN gateway.
Make sure to configure your peer VPN gateway to use MTU of no greater than 1460 bytes.
Check network throughput, both within GCP and your host.
Check if supported IKE ciphers are configured.
It's due to the ufw firewall that is active.
You can check the status by running the command
sudo ufw status
In the output you will see
Status: active
Now just execute
sudo ufw disable
This will disable the firewall and now try reconnecting to the server, internet will work.
Related
How do I confirm that my VM connects to my GCP VPN Gateway? The two are already on the same network. I have tried pinging to the VPN Gateway IP from the vm but I cannot.
You would have to review and make sure that:
The VPN is active under Cloud VPN
Ensure that your GCP and on-prem firewall are allowing ingress/egress traffic between them
Depending on the type of VPN you choose, make sure that the IP address of the VM is shared to your on-prem via BPG, Route or Policy
If you see an issue with the VPN, you can review the VPN logs logs via logging (log viewer) and choose GCE Router. https://cloud.google.com/logging/docs/view/overview
If the issue is with the BGP/Route/Policy based, you would need to ensure your VPN IP is part of the shared range on both side (GCP and on-prem). https://cloud.google.com/network-connectivity/docs/vpn/concepts/overview#classic-vpn
If the issue is with Firewall, make sure that nothing is blocking your VM from communicating with your VPN IP range on GCP side and on your on-prem side. https://cloud.google.com/network-connectivity/docs/vpn/how-to/configuring-firewall-rules
Here is more troubleshooting you can review/try: https://cloud.google.com/network-connectivity/docs/vpn/support/troubleshooting
I run some web services running in Google Compute Engine. I want to secure them and make available only to my coallegues. I don't want to rely on web server security, so my idea was to configure a VPN with Google Cloud Platform.
My question may be silly, because I don't really know how VPN works. Is it possible to create a VPN in Google Cloud and connect to it directly from my laptop? I've tried to use "Hybrid Connectivity VPN" - but it allows only to connect to another VPN. When I make a tunnel, it asks me "Remote peer IP address". I don't have any on-premise VPN in my organization, also I am behind a NAT of my provider.
I know that that it could be possible in principle - once I've connected to VPN of my previous job. I've just used build-in Windows function "Add a VPN connection", inputed IP of the server and the secret. After that I could connect to the servers that were inside the corporate network.
Can I configure Google Cloud VPN to work in similar way?
Client-to-gateway(road warrior) setup is not supported by CloudVPN. For client-to-gateway scenarios, you can install and configure an IPSec VPN software, like Strongswan on a GCE VM and configure it for remote access. Users can than connect to this VPN server through VPN client and, after a secure tunnel established they can connect to all other VMs which are deployed inside the same network. With this setup, you can also configure NAT gateway and remove the public IP from other VMs. Configuring a NAT gateway is described in this article.
https://serverfault.com/questions/818101/does-gcp-support-p2s
I have a Google compute engine vm ubuntu host with stackdriver monitoring agent installed.
The vm host has a VPC firewall rule to deny all communication apart from a proxy server (to get system updates) and it has only an internal IP.
I have configured the stack driver agent according to doc's at https://cloud.google.com/monitoring/agent/install-agent.
The monitoring agent is unable to send monitor data to stackdriver unless i turn off the firewall rule.
What changes should i make to the VPC firewall rule in order for the agent to able to send data to stackdriver?
Stackdriver uses HTTPS to communicate with the Google API endpoints.
However, if your VM only has private IP addresses, you must also configure Private Google Access. I cover the requirements in this article:
https://www.jhanley.com/google-compute-stackdriver-logging-installation-setup-debugging/
These endpoints must be reachable for Stackdriver logging and monitoring to function:
oauth2.googleapis.com
monitoring.googleapis.com
stackdriver.googleapis.com
I would like to run my Node application from EC2. But my application's database is in Client's location and I usually connect through Cisco AnyConnect VPN application.
I tried installing openconnect in the EC2, the moment I connect to the VPN, the instance goes out of my control. I understood this, because I no longer have control on the EC2 instance, since it's in the Client's VPN network. So I rebooted the EC2 to get back the access.
So how can I connect my Client's VPN from EC2 ?
Note: I cannot install or ask my client to configure anything on their end for this, they just provided their VPN connection details.
Create a Gateway in AWS. You can build an IPsec tunnel from AWS to a client's firewall using a site-to-site VPN.
I am trying to connect GCP VPN from my local work station (windows 8.1).
On GCP, I have created Route Based VPN and VPN tunnel as google cloud's documentation. I have used IKEv2 on routing.
On my local computer I have created a VPN over IPSec using shared secret generated from GCP. Here is the screen shot of my local VPN settings:
While connecting the vpn from my windows 8.1 pc, it shows the following error:
and in the GCP side, VPN tunnel status shows:
IKE version mismatch
in the Cloud VPN Gateway log it shows:
establishing IKE_SA failed, peer not responding
It seems IKE version is not matching in both side. Am I missing anything that failed to match IKE version? or any way to enable 'IKEv2' on my windows pc? Any kind of suggestions are welcome.
Thanks in advance!
Cloud VPN is rather end-point to end-point; which may provide tunnels in between networks, with overlapping sub-nets. in order to connect with your client, you'd to setup an OpenVPN Access Server or alike, to provide the gateway which to connect.
As per GCP Cloud VPN features
GCP Cloud VPN uses ESP in Tunnel mode with authentication. Cloud VPN
does not support AH or
ESP in
Transport mode. Note that Cloud VPN does not perform policy-related
filtering on incoming authentication packets. Outgoing packets are
filtered based on the IP range configured on the Cloud VPN gateway.
From your description, I am guessing you are trying to configure remote access VPN which is different from site-to-site VPN and not possible using Cloud VPN in one side and windows machine in another end.
However, as workaround, I would recommend using Strongswan VPN software to set up a VPN gateway on one of your instances. Which is also documented in GCP under "Set up an instance as a VPN gateway" in cases where Cloud VPN doesn't provide the required functionality.