I've searched docs for this but having no luck... Running VMware 8.5.7 for Mac, from the Windows guest I need to reach a port like 8888 that is available to my host (but actually running in VirtualBox on the host -- not sure if that matters but could be important to know.)
Any suggestions? There seem to be very few configuration options for VMware ports, or maybe I'm just looking in the wrong place.)
Thanks
Related
I have installed the latest versions of Virtualbox v.5.2.6 and Vagrant v.2.0.1 on the windows machine with the Intel-Core-i5-4210U-Processor #1.70Ghz 2.40Ghz. I have added the homestead box by running the command:
vagrant box add laravel/homestead
But, on running the vagrant up it runs fine until this point:
Timed out while waiting for the machine to boot. This means that
Vagrant was unable to communicate with the guest machine within the
configured ("config.vm.boot_timeout" value) time period.
If you look above, you should be able to see the error(s) that Vagrant
had when attempting to connect to the machine. These errors are
usually good hints as to what may be wrong.
If you're using a custom box, make sure that networking is properly
working and you're able to connect to the machine. It is a common
problem that networking isn't setup properly in these boxes. Verify
that authentication configurations are also setup properly, as well.
If the box appears to be booting properly, you may want to increase
the timeout ("config.vm.boot_timeout") value.
On running the vagrant ssh-config I get:
Host homestead-7
HostName 127.0.0.1
User vagrant
Port 2222
UserKnownHostsFile /dev/null
StrictHostKeyChecking no
PasswordAuthentication no
IdentityFile C:/Users/MyUser/.vagrant.d/insecure_private_key
IdentitiesOnly yes
LogLevel FATAL
ForwardAgent yes
I have looked around and tried out different things, among others, to uninstall and install again both vagrant and virtualbox, but couldn't find any solution. How can I get this working?
I made VM Ubuntu 16.04 with one network adapter "network bridge" and second adapter "internal network". ClickHouse DBMS installed by default.
Test call within slave Ubuntu curl 'http://localhost:8123/' returns Ok.
But the same call from master Windows host returns nothing :(
Telnet and browser from master OS on http://assignedIP:8123 returns ERR_CONNECTION_REFUSED.
At the same time pings slave Ubintu from master OS and opposite are successful.
How to setup VM's network properly to be able to call ClickHouse on port 8123 from master OS?
Found it!
Have to change
<listen_host>::1</listen_host>
to
<listen_host>::</listen_host>
in /etc/clickhouse-server/config.xml
Could you please check Unbutu firewall status. If it is up, bring it down and try.
I have laravel app which is running in my windows local server. This laravel app is running port:80. I want to load this app in my Ubuntu VirtualBox.
My IP Config:
IPv4 Address : 192.168.8.157
Subnet Mask : 255.255.255.0
Default Gateway: 192.168.8.1
I have config my virtualbox as Bridged Adapter. In my /etc/hosts (ubuntu virtualbox), I have this :
127.0.0.1 localhost
127.0.1.1 asus
192.168.8.157 v2.my.local
I have made a hello word app (node.js) in my local windows which is running on port :3000, and it is running in my VirtualBox by typing v2.my.local:3000, but if I type v2.my.local on my VirtualBox, it is not working (although app is running on windows local machine). it says:
This v2.my.local page can’t be found
Any suggestion? Thanks in Advance.
May be windows firewall blocking connections via port 80. turn off firewall and try it, if it works. Start windows firewall and add firewall rule to allow connections via port 80. If your windows version is 10 then, it will block all virtual box related connections. make sure to add correct rules.
I installed proxmox 4.1 on virtual box and after installationI received the following :
welcome to the proxmox virtual environment.please use your web browser to configure this server - connect to:
https://192.168.56.101:8006
but while trying this https://192.168.56.101:8006 in the browser it is not working
can someone advice !
Check if the VirtualBox Machine Network Adapter is in Bridge Mode. And check that your host and the vm are in the same IP rank (Ex: Windows: 192.168.1.50 & Proxmox: 192.168.1.70)
Your network adapter in VirtualBox has been set to host-only. If you want to connect to it with your PC you'd better set-up bridged networking.
Also when you've did that, change your /etc/hosts file on the Proxmox hosts so that it won't give you any errors while setting up the webserver or any optional clusters.
My vagrant setup for the network is config.vm.network :private_network, ip: "192.168.56.101". If I'm accessing a php page with echo $_SERVER['REMOTE_ADDR']; I got 192.168.56.1 as result. The problem now is that I can't ping 192.168.56.1, so also the config for Xdebug with xdebug.remote_connect_back=1 will fail, because Xdebug tries to connect to 192.168.56.1. If I use my normal ip address with xdebug.remote_host=X.X.X.X everything works fine, but I want to use xdebug.remote_connect_back=1. What can I do that it will work?
I was having the same problem and then started up a Virtualbox manually and realized that I hadn't started a virtualbox since updating and the firewall had to updated. Once I restarted virtualbox I could ping 192.168.56.1 and not have to rely on a hard coded ip address. So, my guess, is that you probably have firewall issues.