Related
What is the difference between "cache unfriendly code" and the "cache friendly" code?
How can I make sure I write cache-efficient code?
Preliminaries
On modern computers, only the lowest level memory structures (the registers) can move data around in single clock cycles. However, registers are very expensive and most computer cores have less than a few dozen registers. At the other end of the memory spectrum (DRAM), the memory is very cheap (i.e. literally millions of times cheaper) but takes hundreds of cycles after a request to receive the data. To bridge this gap between super fast and expensive and super slow and cheap are the cache memories, named L1, L2, L3 in decreasing speed and cost. The idea is that most of the executing code will be hitting a small set of variables often, and the rest (a much larger set of variables) infrequently. If the processor can't find the data in L1 cache, then it looks in L2 cache. If not there, then L3 cache, and if not there, main memory. Each of these "misses" is expensive in time.
(The analogy is cache memory is to system memory, as system memory is to hard disk storage. Hard disk storage is super cheap but very slow).
Caching is one of the main methods to reduce the impact of latency. To paraphrase Herb Sutter (cfr. links below): increasing bandwidth is easy, but we can't buy our way out of latency.
Data is always retrieved through the memory hierarchy (smallest == fastest to slowest). A cache hit/miss usually refers to a hit/miss in the highest level of cache in the CPU -- by highest level I mean the largest == slowest. The cache hit rate is crucial for performance since every cache miss results in fetching data from RAM (or worse ...) which takes a lot of time (hundreds of cycles for RAM, tens of millions of cycles for HDD). In comparison, reading data from the (highest level) cache typically takes only a handful of cycles.
In modern computer architectures, the performance bottleneck is leaving the CPU die (e.g. accessing RAM or higher). This will only get worse over time. The increase in processor frequency is currently no longer relevant to increase performance. The problem is memory access. Hardware design efforts in CPUs therefore currently focus heavily on optimizing caches, prefetching, pipelines and concurrency. For instance, modern CPUs spend around 85% of die on caches and up to 99% for storing/moving data!
There is quite a lot to be said on the subject. Here are a few great references about caches, memory hierarchies and proper programming:
Agner Fog's page. In his excellent documents, you can find detailed examples covering languages ranging from assembly to C++.
If you are into videos, I strongly recommend to have a look at Herb Sutter's talk on machine architecture (youtube) (specifically check 12:00 and onwards!).
Slides about memory optimization by Christer Ericson (director of technology # Sony)
LWN.net's article "What every programmer should know about memory"
Main concepts for cache-friendly code
A very important aspect of cache-friendly code is all about the principle of locality, the goal of which is to place related data close in memory to allow efficient caching. In terms of the CPU cache, it's important to be aware of cache lines to understand how this works: How do cache lines work?
The following particular aspects are of high importance to optimize caching:
Temporal locality: when a given memory location was accessed, it is likely that the same location is accessed again in the near future. Ideally, this information will still be cached at that point.
Spatial locality: this refers to placing related data close to each other. Caching happens on many levels, not just in the CPU. For example, when you read from RAM, typically a larger chunk of memory is fetched than what was specifically asked for because very often the program will require that data soon. HDD caches follow the same line of thought. Specifically for CPU caches, the notion of cache lines is important.
Use appropriate c++ containers
A simple example of cache-friendly versus cache-unfriendly is c++'s std::vector versus std::list. Elements of a std::vector are stored in contiguous memory, and as such accessing them is much more cache-friendly than accessing elements in a std::list, which stores its content all over the place. This is due to spatial locality.
A very nice illustration of this is given by Bjarne Stroustrup in this youtube clip (thanks to #Mohammad Ali Baydoun for the link!).
Don't neglect the cache in data structure and algorithm design
Whenever possible, try to adapt your data structures and order of computations in a way that allows maximum use of the cache. A common technique in this regard is cache blocking (Archive.org version), which is of extreme importance in high-performance computing (cfr. for example ATLAS).
Know and exploit the implicit structure of data
Another simple example, which many people in the field sometimes forget is column-major (ex. fortran,matlab) vs. row-major ordering (ex. c,c++) for storing two dimensional arrays. For example, consider the following matrix:
1 2
3 4
In row-major ordering, this is stored in memory as 1 2 3 4; in column-major ordering, this would be stored as 1 3 2 4. It is easy to see that implementations which do not exploit this ordering will quickly run into (easily avoidable!) cache issues. Unfortunately, I see stuff like this very often in my domain (machine learning). #MatteoItalia showed this example in more detail in his answer.
When fetching a certain element of a matrix from memory, elements near it will be fetched as well and stored in a cache line. If the ordering is exploited, this will result in fewer memory accesses (because the next few values which are needed for subsequent computations are already in a cache line).
For simplicity, assume the cache comprises a single cache line which can contain 2 matrix elements and that when a given element is fetched from memory, the next one is too. Say we want to take the sum over all elements in the example 2x2 matrix above (lets call it M):
Exploiting the ordering (e.g. changing column index first in c++):
M[0][0] (memory) + M[0][1] (cached) + M[1][0] (memory) + M[1][1] (cached)
= 1 + 2 + 3 + 4
--> 2 cache hits, 2 memory accesses
Not exploiting the ordering (e.g. changing row index first in c++):
M[0][0] (memory) + M[1][0] (memory) + M[0][1] (memory) + M[1][1] (memory)
= 1 + 3 + 2 + 4
--> 0 cache hits, 4 memory accesses
In this simple example, exploiting the ordering approximately doubles execution speed (since memory access requires much more cycles than computing the sums). In practice, the performance difference can be much larger.
Avoid unpredictable branches
Modern architectures feature pipelines and compilers are becoming very good at reordering code to minimize delays due to memory access. When your critical code contains (unpredictable) branches, it is hard or impossible to prefetch data. This will indirectly lead to more cache misses.
This is explained very well here (thanks to #0x90 for the link): Why is processing a sorted array faster than processing an unsorted array?
Avoid virtual functions
In the context of c++, virtual methods represent a controversial issue with regard to cache misses (a general consensus exists that they should be avoided when possible in terms of performance). Virtual functions can induce cache misses during look up, but this only happens if the specific function is not called often (otherwise it would likely be cached), so this is regarded as a non-issue by some. For reference about this issue, check out: What is the performance cost of having a virtual method in a C++ class?
Common problems
A common problem in modern architectures with multiprocessor caches is called false sharing. This occurs when each individual processor is attempting to use data in another memory region and attempts to store it in the same cache line. This causes the cache line -- which contains data another processor can use -- to be overwritten again and again. Effectively, different threads make each other wait by inducing cache misses in this situation.
See also (thanks to #Matt for the link): How and when to align to cache line size?
An extreme symptom of poor caching in RAM memory (which is probably not what you mean in this context) is so-called thrashing. This occurs when the process continuously generates page faults (e.g. accesses memory which is not in the current page) which require disk access.
In addition to #Marc Claesen's answer, I think that an instructive classic example of cache-unfriendly code is code that scans a C bidimensional array (e.g. a bitmap image) column-wise instead of row-wise.
Elements that are adjacent in a row are also adjacent in memory, thus accessing them in sequence means accessing them in ascending memory order; this is cache-friendly, since the cache tends to prefetch contiguous blocks of memory.
Instead, accessing such elements column-wise is cache-unfriendly, since elements on the same column are distant in memory from each other (in particular, their distance is equal to the size of the row), so when you use this access pattern you are jumping around in memory, potentially wasting the effort of the cache of retrieving the elements nearby in memory.
And all that it takes to ruin the performance is to go from
// Cache-friendly version - processes pixels which are adjacent in memory
for(unsigned int y=0; y<height; ++y)
{
for(unsigned int x=0; x<width; ++x)
{
... image[y][x] ...
}
}
to
// Cache-unfriendly version - jumps around in memory for no good reason
for(unsigned int x=0; x<width; ++x)
{
for(unsigned int y=0; y<height; ++y)
{
... image[y][x] ...
}
}
This effect can be quite dramatic (several order of magnitudes in speed) in systems with small caches and/or working with big arrays (e.g. 10+ megapixels 24 bpp images on current machines); for this reason, if you have to do many vertical scans, often it's better to rotate the image of 90 degrees first and perform the various analysis later, limiting the cache-unfriendly code just to the rotation.
Optimizing cache usage largely comes down to two factors.
Locality of Reference
The first factor (to which others have already alluded) is locality of reference. Locality of reference really has two dimensions though: space and time.
Spatial
The spatial dimension also comes down to two things: first, we want to pack our information densely, so more information will fit in that limited memory. This means (for example) that you need a major improvement in computational complexity to justify data structures based on small nodes joined by pointers.
Second, we want information that will be processed together also located together. A typical cache works in "lines", which means when you access some information, other information at nearby addresses will be loaded into the cache with the part we touched. For example, when I touch one byte, the cache might load 128 or 256 bytes near that one. To take advantage of that, you generally want the data arranged to maximize the likelihood that you'll also use that other data that was loaded at the same time.
For just a really trivial example, this can mean that a linear search can be much more competitive with a binary search than you'd expect. Once you've loaded one item from a cache line, using the rest of the data in that cache line is almost free. A binary search becomes noticeably faster only when the data is large enough that the binary search reduces the number of cache lines you access.
Time
The time dimension means that when you do some operations on some data, you want (as much as possible) to do all the operations on that data at once.
Since you've tagged this as C++, I'll point to a classic example of a relatively cache-unfriendly design: std::valarray. valarray overloads most arithmetic operators, so I can (for example) say a = b + c + d; (where a, b, c and d are all valarrays) to do element-wise addition of those arrays.
The problem with this is that it walks through one pair of inputs, puts results in a temporary, walks through another pair of inputs, and so on. With a lot of data, the result from one computation may disappear from the cache before it's used in the next computation, so we end up reading (and writing) the data repeatedly before we get our final result. If each element of the final result will be something like (a[n] + b[n]) * (c[n] + d[n]);, we'd generally prefer to read each a[n], b[n], c[n] and d[n] once, do the computation, write the result, increment n and repeat 'til we're done.2
Line Sharing
The second major factor is avoiding line sharing. To understand this, we probably need to back up and look a little at how caches are organized. The simplest form of cache is direct mapped. This means one address in main memory can only be stored in one specific spot in the cache. If we're using two data items that map to the same spot in the cache, it works badly -- each time we use one data item, the other has to be flushed from the cache to make room for the other. The rest of the cache might be empty, but those items won't use other parts of the cache.
To prevent this, most caches are what are called "set associative". For example, in a 4-way set-associative cache, any item from main memory can be stored at any of 4 different places in the cache. So, when the cache is going to load an item, it looks for the least recently used3 item among those four, flushes it to main memory, and loads the new item in its place.
The problem is probably fairly obvious: for a direct-mapped cache, two operands that happen to map to the same cache location can lead to bad behavior. An N-way set-associative cache increases the number from 2 to N+1. Organizing a cache into more "ways" takes extra circuitry and generally runs slower, so (for example) an 8192-way set associative cache is rarely a good solution either.
Ultimately, this factor is more difficult to control in portable code though. Your control over where your data is placed is usually fairly limited. Worse, the exact mapping from address to cache varies between otherwise similar processors. In some cases, however, it can be worth doing things like allocating a large buffer, and then using only parts of what you allocated to ensure against data sharing the same cache lines (even though you'll probably need to detect the exact processor and act accordingly to do this).
False Sharing
There's another, related item called "false sharing". This arises in a multiprocessor or multicore system, where two (or more) processors/cores have data that's separate, but falls in the same cache line. This forces the two processors/cores to coordinate their access to the data, even though each has its own, separate data item. Especially if the two modify the data in alternation, this can lead to a massive slowdown as the data has to be constantly shuttled between the processors. This can't easily be cured by organizing the cache into more "ways" or anything like that either. The primary way to prevent it is to ensure that two threads rarely (preferably never) modify data that could possibly be in the same cache line (with the same caveats about difficulty of controlling the addresses at which data is allocated).
Those who know C++ well might wonder if this is open to optimization via something like expression templates. I'm pretty sure the answer is that yes, it could be done and if it was, it would probably be a pretty substantial win. I'm not aware of anybody having done so, however, and given how little valarray gets used, I'd be at least a little surprised to see anybody do so either.
In case anybody wonders how valarray (designed specifically for performance) could be this badly wrong, it comes down to one thing: it was really designed for machines like the older Crays, that used fast main memory and no cache. For them, this really was a nearly ideal design.
Yes, I'm simplifying: most caches don't really measure the least recently used item precisely, but they use some heuristic that's intended to be close to that without having to keep a full time-stamp for each access.
Welcome to the world of Data Oriented Design. The basic mantra is to Sort, Eliminate Branches, Batch, Eliminate virtual calls - all steps towards better locality.
Since you tagged the question with C++, here's the obligatory typical C++ Bullshit. Tony Albrecht's Pitfalls of Object Oriented Programming is also a great introduction into the subject.
Just piling on: the classic example of cache-unfriendly versus cache-friendly code is the "cache blocking" of matrix multiply.
Naive matrix multiply looks like:
for(i=0;i<N;i++) {
for(j=0;j<N;j++) {
dest[i][j] = 0;
for( k=0;k<N;k++) {
dest[i][j] += src1[i][k] * src2[k][j];
}
}
}
If N is large, e.g. if N * sizeof(elemType) is greater than the cache size, then every single access to src2[k][j] will be a cache miss.
There are many different ways of optimizing this for a cache. Here's a very simple example: instead of reading one item per cache line in the inner loop, use all of the items:
int itemsPerCacheLine = CacheLineSize / sizeof(elemType);
for(i=0;i<N;i++) {
for(j=0;j<N;j += itemsPerCacheLine ) {
for(jj=0;jj<itemsPerCacheLine; jj+) {
dest[i][j+jj] = 0;
}
for( k=0;k<N;k++) {
for(jj=0;jj<itemsPerCacheLine; jj+) {
dest[i][j+jj] += src1[i][k] * src2[k][j+jj];
}
}
}
}
If the cache line size is 64 bytes, and we are operating on 32 bit (4 byte) floats, then there are 16 items per cache line. And the number of cache misses via just this simple transformation is reduced approximately 16-fold.
Fancier transformations operate on 2D tiles, optimize for multiple caches (L1, L2, TLB), and so on.
Some results of googling "cache blocking":
http://stumptown.cc.gt.atl.ga.us/cse6230-hpcta-fa11/slides/11a-matmul-goto.pdf
http://software.intel.com/en-us/articles/cache-blocking-techniques
A nice video animation of an optimized cache blocking algorithm.
http://www.youtube.com/watch?v=IFWgwGMMrh0
Loop tiling is very closely related:
http://en.wikipedia.org/wiki/Loop_tiling
Processors today work with many levels of cascading memory areas. So the CPU will have a bunch of memory that is on the CPU chip itself. It has very fast access to this memory. There are different levels of cache each one slower access ( and larger ) than the next, until you get to system memory which is not on the CPU and is relatively much slower to access.
Logically, to the CPU's instruction set you just refer to memory addresses in a giant virtual address space. When you access a single memory address the CPU will go fetch it. in the old days it would fetch just that single address. But today the CPU will fetch a bunch of memory around the bit you asked for, and copy it into the cache. It assumes that if you asked for a particular address that is is highly likely that you are going to ask for an address nearby very soon. For example if you were copying a buffer you would read and write from consecutive addresses - one right after the other.
So today when you fetch an address it checks the first level of cache to see if it already read that address into cache, if it doesn't find it, then this is a cache miss and it has to go out to the next level of cache to find it, until it eventually has to go out into main memory.
Cache friendly code tries to keep accesses close together in memory so that you minimize cache misses.
So an example would be imagine you wanted to copy a giant 2 dimensional table. It is organized with reach row in consecutive in memory, and one row follow the next right after.
If you copied the elements one row at a time from left to right - that would be cache friendly. If you decided to copy the table one column at a time, you would copy the exact same amount of memory - but it would be cache unfriendly.
It needs to be clarified that not only data should be cache-friendly, it is just as important for the code. This is in addition to branch predicition, instruction reordering, avoiding actual divisions and other techniques.
Typically the denser the code, the fewer cache lines will be required to store it. This results in more cache lines being available for data.
The code should not call functions all over the place as they typically will require one or more cache lines of their own, resulting in fewer cache lines for data.
A function should begin at a cache line-alignment-friendly address. Though there are (gcc) compiler switches for this be aware that if the the functions are very short it might be wasteful for each one to occupy an entire cache line. For example, if three of the most often used functions fit inside one 64 byte cache line, this is less wasteful than if each one has its own line and results in two cache lines less available for other usage. A typical alignment value could be 32 or 16.
So spend some extra time to make the code dense. Test different constructs, compile and review the generated code size and profile.
As #Marc Claesen mentioned that one of the ways to write cache friendly code is to exploit the structure in which our data is stored. In addition to that another way to write cache friendly code is: change the way our data is stored; then write new code to access the data stored in this new structure.
This makes sense in the case of how database systems linearize the tuples of a table and store them. There are two basic ways to store the tuples of a table i.e. row store and column store. In row store as the name suggests the tuples are stored row wise. Lets suppose a table named Product being stored has 3 attributes i.e. int32_t key, char name[56] and int32_t price, so the total size of a tuple is 64 bytes.
We can simulate a very basic row store query execution in main memory by creating an array of Product structs with size N, where N is the number of rows in table. Such memory layout is also called array of structs. So the struct for Product can be like:
struct Product
{
int32_t key;
char name[56];
int32_t price'
}
/* create an array of structs */
Product* table = new Product[N];
/* now load this array of structs, from a file etc. */
Similarly we can simulate a very basic column store query execution in main memory by creating an 3 arrays of size N, one array for each attribute of the Product table. Such memory layout is also called struct of arrays. So the 3 arrays for each attribute of Product can be like:
/* create separate arrays for each attribute */
int32_t* key = new int32_t[N];
char* name = new char[56*N];
int32_t* price = new int32_t[N];
/* now load these arrays, from a file etc. */
Now after loading both the array of structs (Row Layout) and the 3 separate arrays (Column Layout), we have row store and column store on our table Product present in our memory.
Now we move on to the cache friendly code part. Suppose that the workload on our table is such that we have an aggregation query on the price attribute. Such as
SELECT SUM(price)
FROM PRODUCT
For the row store we can convert the above SQL query into
int sum = 0;
for (int i=0; i<N; i++)
sum = sum + table[i].price;
For the column store we can convert the above SQL query into
int sum = 0;
for (int i=0; i<N; i++)
sum = sum + price[i];
The code for the column store would be faster than the code for the row layout in this query as it requires only a subset of attributes and in column layout we are doing just that i.e. only accessing the price column.
Suppose that the cache line size is 64 bytes.
In the case of row layout when a cache line is read, the price value of only 1(cacheline_size/product_struct_size = 64/64 = 1) tuple is read, because our struct size of 64 bytes and it fills our whole cache line, so for every tuple a cache miss occurs in case of a row layout.
In the case of column layout when a cache line is read, the price value of 16(cacheline_size/price_int_size = 64/4 = 16) tuples is read, because 16 contiguous price values stored in memory are brought into the cache, so for every sixteenth tuple a cache miss ocurs in case of column layout.
So the column layout will be faster in the case of given query, and is faster in such aggregation queries on a subset of columns of the table. You can try out such experiment for yourself using the data from TPC-H benchmark, and compare the run times for both the layouts. The wikipedia article on column oriented database systems is also good.
So in database systems, if the query workload is known beforehand, we can store our data in layouts which will suit the queries in workload and access data from these layouts. In the case of above example we created a column layout and changed our code to compute sum so that it became cache friendly.
Be aware that caches do not just cache continuous memory. They have multiple lines (at least 4) so discontinous and overlapping memory can often be stored just as efficiently.
What is missing from all the above examples is measured benchmarks. There are many myths about performance. Unless you measure it you do not know. Do not complicate your code unless you have a measured improvement.
Cache-friendly code is code that has been optimized to make efficient use of the CPU cache. This typically involves organizing data in a way that takes advantage of spatial and temporal locality, which refers to the idea that data that is accessed together is likely to be stored together in memory, and that data that is accessed frequently is likely to be accessed again in the near future.
There are several ways to make code cache-friendly, including:
Using contiguous memory layouts: By storing data in contiguous
blocks in memory, you can take advantage of spatial locality and
reduce the number of cache misses.
Using arrays: Arrays are a good choice for data structures when you
need to access data sequentially, as they allow you to take
advantage of temporal locality and keep hot data in the cache.
Using pointers carefully: Pointers can be used to access data that
is not stored contiguously in memory, but they can also lead to
cache misses if they are used excessively. If you need to use
pointers, try to use them in a way that takes advantage of spatial
and temporal locality to minimize cache misses.
Using compiler optimization flags: Most compilers have optimization
flags that can be used to optimize the use of the CPU cache. These
flags can help to minimize the number of cache misses and improve
the overall performance of your code.
It is important to note that the specific techniques that work best for optimizing the use of the CPU cache will depend on the specific requirements and constraints of your system. It may be necessary to experiment with different approaches to find the best solution for your needs.
I have to read a file in which is stored a matrix with cars (1=BlueCar, 2=RedCar, 0=Empty).
I need to write an algorithm to move the cars of the matrix in that way:
blue ones move downward;
red ones move rightward;
there is a turn in which all the blue ones move and a turn to move all the red ones.
Before the file is read I don't know the matrix size and if it's dense or sparse, so I have to implement two data structures (one for dense and one for sparse) and two algorithms.
I need to reach the best time and space complexity possible.
Due to the unknown matrix size, I think to store the data on the heap.
If the matrix is dense, I think to use something like:
short int** M = new short int*[m];
short int* M_data = new short int[m*n];
for(int i=0; i< m; ++i)
{
M[i] = M_data + i * n;
}
With this structure I can allocate a contiguous space of memory and it is also simple to be accessed with M[i][j].
Now the problem is the structure to choose for the sparse case, and I have to consider also how I can move the cars through the algorithm in the simplest way: for example when I evaluate a car, I need to find easily if in the next position (downward or rightward) there is another car or if it's empty.
Initially I thought to define BlueCar and RedCar objects that inherits from the general Car object. In this objects I can save the matrix coordinates and then put them in:
std::vector<BluCar> sparseBlu;
std::vector<RedCar> sparseRed;
Otherwise I can do something like:
vector< tuple< row, column, value >> sparseMatrix
But the problem of finding what's in the next position still remains.
Probably this is not the best way to do it, so how can I implement the sparse case in a efficient way? (also using a unique structure for sparse)
Why not simply create a memory mapping directly over the file? (assuming your data 0,1,2 is stored in contiguous bytes (or bits) in the file, and the position of those bytes also represents the coordinates of the cars)
This way you don't need to allocate extra memory and read in all the data, and the data can simply and efficiently be accessed with M[i][j].
Going over the rows would be L1-cache friendly.
In case of very sparse data, you could scan through the data once and keep a list of the empty regions/blocks in memory (only need to store startpos and size), which you could then skip (and adjust where needed) in further runs.
With memory mapping, only frequently accessed pages are kept in memory. This means that once you have scanned for the empty regions, memory will only be allocated for the frequently accessed non-empty regions (all this will be done automagically by the kernel - no need to keep track of it yourself).
Another benefit is that you are accessing the OS disk cache directly. Thus no need to keep copying and moving data between kernel space and user space.
To further optimize space- and memory usage, the cars could be stored in 2 bits in the file.
Update:
I'll have to move cars with openMP and MPI... Will the memory mapping
work also with concurrent threads?
You could certainly use multithreading, but not sure if openMP would be the best solution here, because if you work on different parts of the data at the same time, you may need to check some overlapping regions (i.e. a car could move from one block to another).
Or you could let the threads work on the middle parts of the blocks, and then start other threads to do the boundaries (with red cars that would be one byte, with blue cars a full row).
You would also need a locking mechanism for adjusting the list of the sparse regions. I think the best way would be to launch separate threads (depending on the size of the data of course).
In a somewhat similar task, I simply made use of Compressed Row Storage.
The Compressed Row and Column (in the next section) Storage formats
are the most general: they make absolutely no assumptions about the
sparsity structure of the matrix, and they don't store any unnecessary
elements. On the other hand, they are not very efficient, needing an
indirect addressing step for every single scalar operation in a
matrix-vector product or preconditioner solve.
You will need to be a bit more specific about time and space complexity requirements. CSR requires an extra indexing step for simple operations, but that is a minor amount of overhead if you're just doing simple matrix operations.
There's already an existing C++ implementation available online as well.
I am using OpenCL for stereo image processing on the GPU and after I ported a C++ implementation to OpenCL i was playing around with optimizations. A very simple experiment was to swap around the dimensions.
Consider a simple kernel, which is executed for every pixel along the two dimensional work space (f.e. 640x480). In my case it was a Census transform.
Swapping from:
int globalU = get_global_id(0);
int globalV = get_global_id(1);
too
int globalU = get_global_id(1);
int globalV = get_global_id(0);
while adjusting the NDRange in the same way, gave a performance boost about 500%. Other experiments in 3d Space achieved a execution time from 72ms to 2ms, only with reordering of the dimensions.
Can anybody explain my, how this happens?
Is it just an effect of memory pipelines and cache usage?
EDIT: The image has a standart mamory layout. Thats why i wondered about the effects. I expected the best speed, when the iteration goes like the image is stored in the memory, which is not the case.
After some reading of the AMD APP SDK documantation, i found some interesting details about the memory channels. That could be a reason.
When you access an element in a memory in first being loaded into a CPU's cache. CPU does not load single element (say 1 byte), but instead it loads a single line (for example 64 adjacent bytes) into cache. This is because it is usually likely that you will access subsequent elements, so CPU would not need to access RAM again.
This is make a huge difference since to access cache memory, an electrical signal should not even leave CPU chip, while if CPU need to load data from RAM, the signal need to travel to a separate chip and probably more then one signal from CPU is required since it generally need to specify row and column in RAM to access part of it (Read What every programmer should know about memory for more info). In practice access time to cache may take only 0.5 ns while RAM access will cost 100 ns.
So computer algorithms should take this into account. If you traverse through all elements in a matrix, you should traverse them so you would access elements that are located near each other approximately at the same time. So if your matrix has the following layout in memory:
m_0_0, m_0_1, m_0_2, ... m_1_0, m_1_1 (first column, second column, etc.)
you should access elements in order: m_0_0, m_0_1, m_0_2 (by column)
If you would use different access order (say by row in this case), CPU would load part of first column in cache when you access first element in first column, then part of second column when you access first element in second column etc. When you will traverse first row and access second element in first column cache values for the first column would no longer be present in cache, since it has limited (and very small) size. Therefore such an algorithm would effectively eliminate cache at all.
What is the difference between "cache unfriendly code" and the "cache friendly" code?
How can I make sure I write cache-efficient code?
Preliminaries
On modern computers, only the lowest level memory structures (the registers) can move data around in single clock cycles. However, registers are very expensive and most computer cores have less than a few dozen registers. At the other end of the memory spectrum (DRAM), the memory is very cheap (i.e. literally millions of times cheaper) but takes hundreds of cycles after a request to receive the data. To bridge this gap between super fast and expensive and super slow and cheap are the cache memories, named L1, L2, L3 in decreasing speed and cost. The idea is that most of the executing code will be hitting a small set of variables often, and the rest (a much larger set of variables) infrequently. If the processor can't find the data in L1 cache, then it looks in L2 cache. If not there, then L3 cache, and if not there, main memory. Each of these "misses" is expensive in time.
(The analogy is cache memory is to system memory, as system memory is to hard disk storage. Hard disk storage is super cheap but very slow).
Caching is one of the main methods to reduce the impact of latency. To paraphrase Herb Sutter (cfr. links below): increasing bandwidth is easy, but we can't buy our way out of latency.
Data is always retrieved through the memory hierarchy (smallest == fastest to slowest). A cache hit/miss usually refers to a hit/miss in the highest level of cache in the CPU -- by highest level I mean the largest == slowest. The cache hit rate is crucial for performance since every cache miss results in fetching data from RAM (or worse ...) which takes a lot of time (hundreds of cycles for RAM, tens of millions of cycles for HDD). In comparison, reading data from the (highest level) cache typically takes only a handful of cycles.
In modern computer architectures, the performance bottleneck is leaving the CPU die (e.g. accessing RAM or higher). This will only get worse over time. The increase in processor frequency is currently no longer relevant to increase performance. The problem is memory access. Hardware design efforts in CPUs therefore currently focus heavily on optimizing caches, prefetching, pipelines and concurrency. For instance, modern CPUs spend around 85% of die on caches and up to 99% for storing/moving data!
There is quite a lot to be said on the subject. Here are a few great references about caches, memory hierarchies and proper programming:
Agner Fog's page. In his excellent documents, you can find detailed examples covering languages ranging from assembly to C++.
If you are into videos, I strongly recommend to have a look at Herb Sutter's talk on machine architecture (youtube) (specifically check 12:00 and onwards!).
Slides about memory optimization by Christer Ericson (director of technology # Sony)
LWN.net's article "What every programmer should know about memory"
Main concepts for cache-friendly code
A very important aspect of cache-friendly code is all about the principle of locality, the goal of which is to place related data close in memory to allow efficient caching. In terms of the CPU cache, it's important to be aware of cache lines to understand how this works: How do cache lines work?
The following particular aspects are of high importance to optimize caching:
Temporal locality: when a given memory location was accessed, it is likely that the same location is accessed again in the near future. Ideally, this information will still be cached at that point.
Spatial locality: this refers to placing related data close to each other. Caching happens on many levels, not just in the CPU. For example, when you read from RAM, typically a larger chunk of memory is fetched than what was specifically asked for because very often the program will require that data soon. HDD caches follow the same line of thought. Specifically for CPU caches, the notion of cache lines is important.
Use appropriate c++ containers
A simple example of cache-friendly versus cache-unfriendly is c++'s std::vector versus std::list. Elements of a std::vector are stored in contiguous memory, and as such accessing them is much more cache-friendly than accessing elements in a std::list, which stores its content all over the place. This is due to spatial locality.
A very nice illustration of this is given by Bjarne Stroustrup in this youtube clip (thanks to #Mohammad Ali Baydoun for the link!).
Don't neglect the cache in data structure and algorithm design
Whenever possible, try to adapt your data structures and order of computations in a way that allows maximum use of the cache. A common technique in this regard is cache blocking (Archive.org version), which is of extreme importance in high-performance computing (cfr. for example ATLAS).
Know and exploit the implicit structure of data
Another simple example, which many people in the field sometimes forget is column-major (ex. fortran,matlab) vs. row-major ordering (ex. c,c++) for storing two dimensional arrays. For example, consider the following matrix:
1 2
3 4
In row-major ordering, this is stored in memory as 1 2 3 4; in column-major ordering, this would be stored as 1 3 2 4. It is easy to see that implementations which do not exploit this ordering will quickly run into (easily avoidable!) cache issues. Unfortunately, I see stuff like this very often in my domain (machine learning). #MatteoItalia showed this example in more detail in his answer.
When fetching a certain element of a matrix from memory, elements near it will be fetched as well and stored in a cache line. If the ordering is exploited, this will result in fewer memory accesses (because the next few values which are needed for subsequent computations are already in a cache line).
For simplicity, assume the cache comprises a single cache line which can contain 2 matrix elements and that when a given element is fetched from memory, the next one is too. Say we want to take the sum over all elements in the example 2x2 matrix above (lets call it M):
Exploiting the ordering (e.g. changing column index first in c++):
M[0][0] (memory) + M[0][1] (cached) + M[1][0] (memory) + M[1][1] (cached)
= 1 + 2 + 3 + 4
--> 2 cache hits, 2 memory accesses
Not exploiting the ordering (e.g. changing row index first in c++):
M[0][0] (memory) + M[1][0] (memory) + M[0][1] (memory) + M[1][1] (memory)
= 1 + 3 + 2 + 4
--> 0 cache hits, 4 memory accesses
In this simple example, exploiting the ordering approximately doubles execution speed (since memory access requires much more cycles than computing the sums). In practice, the performance difference can be much larger.
Avoid unpredictable branches
Modern architectures feature pipelines and compilers are becoming very good at reordering code to minimize delays due to memory access. When your critical code contains (unpredictable) branches, it is hard or impossible to prefetch data. This will indirectly lead to more cache misses.
This is explained very well here (thanks to #0x90 for the link): Why is processing a sorted array faster than processing an unsorted array?
Avoid virtual functions
In the context of c++, virtual methods represent a controversial issue with regard to cache misses (a general consensus exists that they should be avoided when possible in terms of performance). Virtual functions can induce cache misses during look up, but this only happens if the specific function is not called often (otherwise it would likely be cached), so this is regarded as a non-issue by some. For reference about this issue, check out: What is the performance cost of having a virtual method in a C++ class?
Common problems
A common problem in modern architectures with multiprocessor caches is called false sharing. This occurs when each individual processor is attempting to use data in another memory region and attempts to store it in the same cache line. This causes the cache line -- which contains data another processor can use -- to be overwritten again and again. Effectively, different threads make each other wait by inducing cache misses in this situation.
See also (thanks to #Matt for the link): How and when to align to cache line size?
An extreme symptom of poor caching in RAM memory (which is probably not what you mean in this context) is so-called thrashing. This occurs when the process continuously generates page faults (e.g. accesses memory which is not in the current page) which require disk access.
In addition to #Marc Claesen's answer, I think that an instructive classic example of cache-unfriendly code is code that scans a C bidimensional array (e.g. a bitmap image) column-wise instead of row-wise.
Elements that are adjacent in a row are also adjacent in memory, thus accessing them in sequence means accessing them in ascending memory order; this is cache-friendly, since the cache tends to prefetch contiguous blocks of memory.
Instead, accessing such elements column-wise is cache-unfriendly, since elements on the same column are distant in memory from each other (in particular, their distance is equal to the size of the row), so when you use this access pattern you are jumping around in memory, potentially wasting the effort of the cache of retrieving the elements nearby in memory.
And all that it takes to ruin the performance is to go from
// Cache-friendly version - processes pixels which are adjacent in memory
for(unsigned int y=0; y<height; ++y)
{
for(unsigned int x=0; x<width; ++x)
{
... image[y][x] ...
}
}
to
// Cache-unfriendly version - jumps around in memory for no good reason
for(unsigned int x=0; x<width; ++x)
{
for(unsigned int y=0; y<height; ++y)
{
... image[y][x] ...
}
}
This effect can be quite dramatic (several order of magnitudes in speed) in systems with small caches and/or working with big arrays (e.g. 10+ megapixels 24 bpp images on current machines); for this reason, if you have to do many vertical scans, often it's better to rotate the image of 90 degrees first and perform the various analysis later, limiting the cache-unfriendly code just to the rotation.
Optimizing cache usage largely comes down to two factors.
Locality of Reference
The first factor (to which others have already alluded) is locality of reference. Locality of reference really has two dimensions though: space and time.
Spatial
The spatial dimension also comes down to two things: first, we want to pack our information densely, so more information will fit in that limited memory. This means (for example) that you need a major improvement in computational complexity to justify data structures based on small nodes joined by pointers.
Second, we want information that will be processed together also located together. A typical cache works in "lines", which means when you access some information, other information at nearby addresses will be loaded into the cache with the part we touched. For example, when I touch one byte, the cache might load 128 or 256 bytes near that one. To take advantage of that, you generally want the data arranged to maximize the likelihood that you'll also use that other data that was loaded at the same time.
For just a really trivial example, this can mean that a linear search can be much more competitive with a binary search than you'd expect. Once you've loaded one item from a cache line, using the rest of the data in that cache line is almost free. A binary search becomes noticeably faster only when the data is large enough that the binary search reduces the number of cache lines you access.
Time
The time dimension means that when you do some operations on some data, you want (as much as possible) to do all the operations on that data at once.
Since you've tagged this as C++, I'll point to a classic example of a relatively cache-unfriendly design: std::valarray. valarray overloads most arithmetic operators, so I can (for example) say a = b + c + d; (where a, b, c and d are all valarrays) to do element-wise addition of those arrays.
The problem with this is that it walks through one pair of inputs, puts results in a temporary, walks through another pair of inputs, and so on. With a lot of data, the result from one computation may disappear from the cache before it's used in the next computation, so we end up reading (and writing) the data repeatedly before we get our final result. If each element of the final result will be something like (a[n] + b[n]) * (c[n] + d[n]);, we'd generally prefer to read each a[n], b[n], c[n] and d[n] once, do the computation, write the result, increment n and repeat 'til we're done.2
Line Sharing
The second major factor is avoiding line sharing. To understand this, we probably need to back up and look a little at how caches are organized. The simplest form of cache is direct mapped. This means one address in main memory can only be stored in one specific spot in the cache. If we're using two data items that map to the same spot in the cache, it works badly -- each time we use one data item, the other has to be flushed from the cache to make room for the other. The rest of the cache might be empty, but those items won't use other parts of the cache.
To prevent this, most caches are what are called "set associative". For example, in a 4-way set-associative cache, any item from main memory can be stored at any of 4 different places in the cache. So, when the cache is going to load an item, it looks for the least recently used3 item among those four, flushes it to main memory, and loads the new item in its place.
The problem is probably fairly obvious: for a direct-mapped cache, two operands that happen to map to the same cache location can lead to bad behavior. An N-way set-associative cache increases the number from 2 to N+1. Organizing a cache into more "ways" takes extra circuitry and generally runs slower, so (for example) an 8192-way set associative cache is rarely a good solution either.
Ultimately, this factor is more difficult to control in portable code though. Your control over where your data is placed is usually fairly limited. Worse, the exact mapping from address to cache varies between otherwise similar processors. In some cases, however, it can be worth doing things like allocating a large buffer, and then using only parts of what you allocated to ensure against data sharing the same cache lines (even though you'll probably need to detect the exact processor and act accordingly to do this).
False Sharing
There's another, related item called "false sharing". This arises in a multiprocessor or multicore system, where two (or more) processors/cores have data that's separate, but falls in the same cache line. This forces the two processors/cores to coordinate their access to the data, even though each has its own, separate data item. Especially if the two modify the data in alternation, this can lead to a massive slowdown as the data has to be constantly shuttled between the processors. This can't easily be cured by organizing the cache into more "ways" or anything like that either. The primary way to prevent it is to ensure that two threads rarely (preferably never) modify data that could possibly be in the same cache line (with the same caveats about difficulty of controlling the addresses at which data is allocated).
Those who know C++ well might wonder if this is open to optimization via something like expression templates. I'm pretty sure the answer is that yes, it could be done and if it was, it would probably be a pretty substantial win. I'm not aware of anybody having done so, however, and given how little valarray gets used, I'd be at least a little surprised to see anybody do so either.
In case anybody wonders how valarray (designed specifically for performance) could be this badly wrong, it comes down to one thing: it was really designed for machines like the older Crays, that used fast main memory and no cache. For them, this really was a nearly ideal design.
Yes, I'm simplifying: most caches don't really measure the least recently used item precisely, but they use some heuristic that's intended to be close to that without having to keep a full time-stamp for each access.
Welcome to the world of Data Oriented Design. The basic mantra is to Sort, Eliminate Branches, Batch, Eliminate virtual calls - all steps towards better locality.
Since you tagged the question with C++, here's the obligatory typical C++ Bullshit. Tony Albrecht's Pitfalls of Object Oriented Programming is also a great introduction into the subject.
Just piling on: the classic example of cache-unfriendly versus cache-friendly code is the "cache blocking" of matrix multiply.
Naive matrix multiply looks like:
for(i=0;i<N;i++) {
for(j=0;j<N;j++) {
dest[i][j] = 0;
for( k=0;k<N;k++) {
dest[i][j] += src1[i][k] * src2[k][j];
}
}
}
If N is large, e.g. if N * sizeof(elemType) is greater than the cache size, then every single access to src2[k][j] will be a cache miss.
There are many different ways of optimizing this for a cache. Here's a very simple example: instead of reading one item per cache line in the inner loop, use all of the items:
int itemsPerCacheLine = CacheLineSize / sizeof(elemType);
for(i=0;i<N;i++) {
for(j=0;j<N;j += itemsPerCacheLine ) {
for(jj=0;jj<itemsPerCacheLine; jj+) {
dest[i][j+jj] = 0;
}
for( k=0;k<N;k++) {
for(jj=0;jj<itemsPerCacheLine; jj+) {
dest[i][j+jj] += src1[i][k] * src2[k][j+jj];
}
}
}
}
If the cache line size is 64 bytes, and we are operating on 32 bit (4 byte) floats, then there are 16 items per cache line. And the number of cache misses via just this simple transformation is reduced approximately 16-fold.
Fancier transformations operate on 2D tiles, optimize for multiple caches (L1, L2, TLB), and so on.
Some results of googling "cache blocking":
http://stumptown.cc.gt.atl.ga.us/cse6230-hpcta-fa11/slides/11a-matmul-goto.pdf
http://software.intel.com/en-us/articles/cache-blocking-techniques
A nice video animation of an optimized cache blocking algorithm.
http://www.youtube.com/watch?v=IFWgwGMMrh0
Loop tiling is very closely related:
http://en.wikipedia.org/wiki/Loop_tiling
Processors today work with many levels of cascading memory areas. So the CPU will have a bunch of memory that is on the CPU chip itself. It has very fast access to this memory. There are different levels of cache each one slower access ( and larger ) than the next, until you get to system memory which is not on the CPU and is relatively much slower to access.
Logically, to the CPU's instruction set you just refer to memory addresses in a giant virtual address space. When you access a single memory address the CPU will go fetch it. in the old days it would fetch just that single address. But today the CPU will fetch a bunch of memory around the bit you asked for, and copy it into the cache. It assumes that if you asked for a particular address that is is highly likely that you are going to ask for an address nearby very soon. For example if you were copying a buffer you would read and write from consecutive addresses - one right after the other.
So today when you fetch an address it checks the first level of cache to see if it already read that address into cache, if it doesn't find it, then this is a cache miss and it has to go out to the next level of cache to find it, until it eventually has to go out into main memory.
Cache friendly code tries to keep accesses close together in memory so that you minimize cache misses.
So an example would be imagine you wanted to copy a giant 2 dimensional table. It is organized with reach row in consecutive in memory, and one row follow the next right after.
If you copied the elements one row at a time from left to right - that would be cache friendly. If you decided to copy the table one column at a time, you would copy the exact same amount of memory - but it would be cache unfriendly.
It needs to be clarified that not only data should be cache-friendly, it is just as important for the code. This is in addition to branch predicition, instruction reordering, avoiding actual divisions and other techniques.
Typically the denser the code, the fewer cache lines will be required to store it. This results in more cache lines being available for data.
The code should not call functions all over the place as they typically will require one or more cache lines of their own, resulting in fewer cache lines for data.
A function should begin at a cache line-alignment-friendly address. Though there are (gcc) compiler switches for this be aware that if the the functions are very short it might be wasteful for each one to occupy an entire cache line. For example, if three of the most often used functions fit inside one 64 byte cache line, this is less wasteful than if each one has its own line and results in two cache lines less available for other usage. A typical alignment value could be 32 or 16.
So spend some extra time to make the code dense. Test different constructs, compile and review the generated code size and profile.
As #Marc Claesen mentioned that one of the ways to write cache friendly code is to exploit the structure in which our data is stored. In addition to that another way to write cache friendly code is: change the way our data is stored; then write new code to access the data stored in this new structure.
This makes sense in the case of how database systems linearize the tuples of a table and store them. There are two basic ways to store the tuples of a table i.e. row store and column store. In row store as the name suggests the tuples are stored row wise. Lets suppose a table named Product being stored has 3 attributes i.e. int32_t key, char name[56] and int32_t price, so the total size of a tuple is 64 bytes.
We can simulate a very basic row store query execution in main memory by creating an array of Product structs with size N, where N is the number of rows in table. Such memory layout is also called array of structs. So the struct for Product can be like:
struct Product
{
int32_t key;
char name[56];
int32_t price'
}
/* create an array of structs */
Product* table = new Product[N];
/* now load this array of structs, from a file etc. */
Similarly we can simulate a very basic column store query execution in main memory by creating an 3 arrays of size N, one array for each attribute of the Product table. Such memory layout is also called struct of arrays. So the 3 arrays for each attribute of Product can be like:
/* create separate arrays for each attribute */
int32_t* key = new int32_t[N];
char* name = new char[56*N];
int32_t* price = new int32_t[N];
/* now load these arrays, from a file etc. */
Now after loading both the array of structs (Row Layout) and the 3 separate arrays (Column Layout), we have row store and column store on our table Product present in our memory.
Now we move on to the cache friendly code part. Suppose that the workload on our table is such that we have an aggregation query on the price attribute. Such as
SELECT SUM(price)
FROM PRODUCT
For the row store we can convert the above SQL query into
int sum = 0;
for (int i=0; i<N; i++)
sum = sum + table[i].price;
For the column store we can convert the above SQL query into
int sum = 0;
for (int i=0; i<N; i++)
sum = sum + price[i];
The code for the column store would be faster than the code for the row layout in this query as it requires only a subset of attributes and in column layout we are doing just that i.e. only accessing the price column.
Suppose that the cache line size is 64 bytes.
In the case of row layout when a cache line is read, the price value of only 1(cacheline_size/product_struct_size = 64/64 = 1) tuple is read, because our struct size of 64 bytes and it fills our whole cache line, so for every tuple a cache miss occurs in case of a row layout.
In the case of column layout when a cache line is read, the price value of 16(cacheline_size/price_int_size = 64/4 = 16) tuples is read, because 16 contiguous price values stored in memory are brought into the cache, so for every sixteenth tuple a cache miss ocurs in case of column layout.
So the column layout will be faster in the case of given query, and is faster in such aggregation queries on a subset of columns of the table. You can try out such experiment for yourself using the data from TPC-H benchmark, and compare the run times for both the layouts. The wikipedia article on column oriented database systems is also good.
So in database systems, if the query workload is known beforehand, we can store our data in layouts which will suit the queries in workload and access data from these layouts. In the case of above example we created a column layout and changed our code to compute sum so that it became cache friendly.
Be aware that caches do not just cache continuous memory. They have multiple lines (at least 4) so discontinous and overlapping memory can often be stored just as efficiently.
What is missing from all the above examples is measured benchmarks. There are many myths about performance. Unless you measure it you do not know. Do not complicate your code unless you have a measured improvement.
Cache-friendly code is code that has been optimized to make efficient use of the CPU cache. This typically involves organizing data in a way that takes advantage of spatial and temporal locality, which refers to the idea that data that is accessed together is likely to be stored together in memory, and that data that is accessed frequently is likely to be accessed again in the near future.
There are several ways to make code cache-friendly, including:
Using contiguous memory layouts: By storing data in contiguous
blocks in memory, you can take advantage of spatial locality and
reduce the number of cache misses.
Using arrays: Arrays are a good choice for data structures when you
need to access data sequentially, as they allow you to take
advantage of temporal locality and keep hot data in the cache.
Using pointers carefully: Pointers can be used to access data that
is not stored contiguously in memory, but they can also lead to
cache misses if they are used excessively. If you need to use
pointers, try to use them in a way that takes advantage of spatial
and temporal locality to minimize cache misses.
Using compiler optimization flags: Most compilers have optimization
flags that can be used to optimize the use of the CPU cache. These
flags can help to minimize the number of cache misses and improve
the overall performance of your code.
It is important to note that the specific techniques that work best for optimizing the use of the CPU cache will depend on the specific requirements and constraints of your system. It may be necessary to experiment with different approaches to find the best solution for your needs.
I'm writing a C++ library for an image format that is based on PNG. One stopping point for me is that I'm unsure as to how I ought to lay out the pixel data in memory; as far as I'm aware, there are two practical approaches:
An array of size (width * height); each pixel can be accessed by array[y*width + x].
An array of size (height), containing pointers to arrays of size (width).
The standard reference implementation for PNG (libpng) uses method 2 of the above, while I've seen others use method 1. Is one better than the other, or is each a method with its own pros and cons, to where a compromise must be made? Further, which format do most graphical display systems use (perhaps for ease of using the output of my library into other APIs)?
Off the top of my head:
The one thing that would make me choose #2 is the fact that your memory requirements are a little relaxed. If you were to go for #1, the system will need to be able to allocate height * width amount of contiguous memory. Whereas, in case of #2, it has the freedom to allocate smaller chunks of contiguous memory of size width (could as well be height) off of areas that are free. (When you factor in the channels per pixel, the #1 may fail for even moderately sized images.)
Further, it may be slightly better when swapping rows (or columns) if required for image manipulation purposes (pointer swap suffices).
The downside for #2 is of course an extra level of indirection that seeps in for every access and the array of pointers to be maintained. But this is hardly a matter given todays processor speed and memory.
The second downside for #2 is that the data isn't necessarily next to each other, which makes it harder for the processor the load the right memory pages into the cache.
The advantage of method 2 (cutting up the array in rows) is that you can perform memory operations in steps, e.g. resizing or shuffling the image without reallocating the entire chunk of memory at once. For really large images this may be an advantage.
The advantage of a single array is that you calculations are simpler, i.e. to go one row down you do
pos += width;
instead of having to reference pointers. For small to medium images this is probably faster. Unless you're dealing with images of hundreds of Mb, I would go with method 1.
I suspect that libpng does that (style 2) for a few possible reasons:
Avoid large allocations (as mentioned), and may ease handling VERY large PNGs, especially in systems without VM
(perhaps) allow for interleaved decode ala interleaved JPEG (if PNG supports that)
Ease of certain transformations (vertical flip) (unlikely)
Ease of scaling (insert or remove lines without needing a full second buffer, or widen/narrow lines) (unlikely but possible)
The problem with this approach (assuming each line is an allocation) is a LOT more allocation/free overhead, and perhaps encourage memory fragmentation.
Unless you have a good reason, use style 1 (single allocation), and perhaps round to a "good" boundary for the architecture you're using (could be 4, 8, 16 or perhaps even more bytes). Note that many library functions may look for style 1 with no padding - think about how you'll be using this and where you'll be passing them to.
Windows itself uses a variation of method 1. Each row of the image is padded to a multiple of 4 bytes, and the order of the colors is B,G,R instead of the more normal R,G,B. Also the first row of the buffer is the bottom row of the image.