I'm trying to figure out how to setup network in virtualbox for a linuxserver.
I want the server to be able to go to the internet, on the other hand I need it to have the same ip so I can add url's to my host's hostfile to access the websites on the server in the virtualbox.
Using NAT I have no control over the ip (i am often in different networks too)
using host-only the server has no internet..
What way should I go here?
Related
I didn't find such guide or articles how to do it for ElasticSearch hosted on Windows server.
I have the EC2 amazon windows instance which running ElasticSearch server on port 9200, but I can't achieve it by _ec2_ip_adress:9200 outside the server.
I completely sure that all TCP ports are opened in amazon security group rules, I've turned off the firewall on the server as well.
So that is the problem in ElasticSearch configs.
Can someone help me with that?
Well but you know that then any body would be able to delete/create stuff in your index until you have shield.
If you really want to open it, also make sure that in windows firewall you opened port 9200.
So what i would do i would probably restrict in firewall on in Amazon access to this port for specific IPs (Actually in my project i am doing that :) )
There is one more thing to check on which IP is runned as soon as i remember ES will run on private IP. Look to network.host default is __local__. Try network.host: 0.0.0.0
I've installed pfsense 2.3 x64 in virtualbox with 2 adapters; One is bridged to my wifi adapter (adsl modem) (WAN) and the other one set as'Internal network' ('intnet') (Lan);
The problem is that although pfsense can automatically detect dhcp over first adapter and get an IP but my system (the host) can not ping the pfsense server (pfsense can ping both adsl modem gateway and the host).
Note1: Disabling the antivirus and firewall (kaspersky internet security 2016) has no effect.
Note2: I know that this setup works because I use the exact same network configurations for a Kerio Control server (v9.0.2, installed in virtualbox)
Note3: If I constantly ping pfsense server in my host (ping 192.168.1.102 -t) and at the same time restart pfsense server, during the booting phase of pfsense I can get two pings!
After contacting the pfsense official forum, it turned out that the WAN interface blocks everything by default. Therefore, either a rule should be defined to allow WAN to accept traffic or access server from LAN side.
I figured this out without having to go through the WAN interface, answer is on the pfsense forum
Configure host-only network "vboxnet1" (or any of the other host-only networks if you're already using vboxnet1 for other VMs) with the following:
192.168.1.77 (or whatever IP you want your host to appear as on the network)
255.255.255.0
DHCP Disabled
The make sure that the LAN adapter on your pfSense VM is a "Host-only Adapter" and that it's using "vboxnet1" (or whatever network you configured above)
Reboot/re-install and http://192.168.1.1 should work now
I have a single Windows Amazon EC2 instance and one public IP. The instance is running multiple web server EXEs which all sit on port 80. I want to have different domain names which I want to point to each server. On my old dedicated server I achieved this simply by having different public IPs, but with Amazon EC2 I want to keep to just one public IP.
I am not using IIS, Apache, etc. otherwise life would be a lot simpler (I would simply bind hostnames accordingly). The web server executables perform unusual "utility" tasks as part of a range of other websites, but still need to be hosted on port 80. There is no configuration other than address to bind to and port #.
I have setup several private IPs and bound each server application to those private IPs. Is it possible to leverage some of the Amazon networking products to direct the traffic to the correct private IP? e.g. I have tried setting up a private-DNS using Amazon Route53, and internally at least this seems to point to the correct servers - but not (perhaps logically) when I try to access the site externally.
In absence of any other solutions I decided to solve this using the blunt hammer approach and use a reverse proxy. Downside is my servers now only see the user IPs as 127.0.0.1 which was less than ideal, but better than nothing at all.
For my reverse proxy I used Redbird (uses node.js) but Nginx may also be an option. Both are free / open source.
Basically, my internal IP is masked by an external IP of my internet service provider. So, my internal IP can only be accessed inside my intranet. I want to let users outside the intranet to access my Dev server as well which is hosted on 0.0.0.0:8000 on my system. How do I do that?
Check out localtunnel on github, it does exactly what you're asking.
https://github.com/progrium/localtunnel
If you are willing to go that far you can use Reverse SSH Tunnel:
open a free micro linux instance on Amazon's AWS and create a reverse SSH tunnel to redirect port 80 on the server to your machine.
This is a cool solution for testing purposes and low traffic usage...
You can read more about it here:
http://www.techrepublic.com/article/setting-up-a-reverse-ssh-tunnel/5779944
I’m developing a small application that interacts with a web service which authorizes access based on the client IP. When developing on my local machine at home, I am not allow to access the web service, unless I request an authorization for the random IP that i get from my ISP.
My question: Is there an easy way to get around this problem, since I cannot have a fixed IP at home? Proxy, vpn, etc... through a webserver with an authorized IP? How?
Thanks in advance :)
I assume this is your problem: You can only connect to remote_system from Authorized_IP system.
If you can ssh to Authorized_IP from your home PC, you can setup a ssh tunnel that forward connection to port 8080 of Authorized_IP to the port 80 of the remote_system with ssh command. If you run Linux on the Authorized_IP system, it is very simple. Windows is more complex with Cygwin sshd, it is possible.
http://www.google.com/search?q=ssh+tunnel
To answer your question directly: Dynamic DNS. For testing, point your web service at a hostname that your get from a dynamic DNS provider such as http://dyndns.org. Then download a tool that automatically updates your DNS entry with your dynamically assigned IP address.
But more to the point, why can't you just use your localhost (127.0.0.1) as your IP address for developing, debugging, testing?