If I have a Catmull-Rom spline of a certain length how can I calculate its position at a certain distance? Typically to calculate the point in a catmull rom spline you input a value between 0 and 1 to get its position via proportions, how can I do this for distances? For example if my spline is 30 units long how can I get its position at distance 8?
The reason I ask is because it seems with catmull rom splines giving points in the [0,1] domain does not guarantee that it will give you the point at that distance into the spline, for example if I input 0.5 into a catmull romspline of length 30 it does not mean I'll get the position at the distance of 15 of the spline unless the spline itself is in effect a straight line..
The usual way is to store length of each segment and then to find out the partial length of a segment you increment t by an epsilon value and calculate the linear distance between the 2 points until you hit your answer. Obviously the smaller your epsilon the better the result you get but it gives surprisingly good results. I used this method for moving at a constant speed along a catmul-rom and you cannot see it speed up and slow down ... it DOES move at a constant speed. Obviously depending on how tight your segments are your epsilon value will need to change but, in general, you can pick a "good enough" epsilon and everything will be fine.
Findinf the answer non-iteratively is INCREDIBLY expensive (I have seen the derivation a while back and it was not pretty ;)). You will have to have a tiny epsilon value to get worse performance ...
Another link:
Adaptive Subdivision of Bezier Curves in the Anti-Grain Geometry library
is mainly on the different problem of drawing Bezier curves on a grid of pixels
with a wide brush, but see the very end.
(Added:) Antigrain also has a lovely examples/bspline.cpp
in which you can move knots and vary the number of intermediate points.
Goz's answer is accurate - here's a related discussion about length of Bezier curves. The summary of the posters was that it's less computation (and much simpler) to do an approximation than compute the exact answer. This is applicable because you can change the basis of parametric splines, so you could convert the Catmull-Rom curve to Bezier segments.
For approximation, you're basically breaking it into primitives with simple analytical length, then summing all of the simple lengths. While most people use line segments, you do tend to have shrinkage. You can minimize the error by using small segments, but your approximation will always be less than the true length for non-linear curves.
If you need more accuracy there's a paper from jgt that discusses how to use circles as your approximation primitives, which is apparently faster/more accurate but not much harder to implement. They include a sample C implementation.
Related
I have:
- a set of points of known size (in my case, only 6 points)
- a line characterized by x = s + t * r, where x, s and r are 3D vectors
I need to find the point closest to the given line. The actual distance does not matter to me.
I had a look at several different questions that seem related (including this one) and know how to solve this on paper from my highschool math classes. But I cannot find a solution without calculating every distance, and I am sure there has to be a better/faster way. Performance is absolutely crucial in my application.
One more thing: All numbers are integers (coordinates of points and elements of s and r vectors). Again, for performance reasons I would like to keep the floating-point math to a minimum.
You have to process every point at least once to know their distance. Unless you want to repeat the process many times with different lines, simply computing the distance of every point is unavoidable. So the algorithm has to be O(n).
Since you don't care about the actual distance, we can make some simplification to the point-distance computation. The exact distance is computed by (source):
d^2 = |r⨯(p-s)|^2 / |r|^2
where ⨯ is the cross product and |r|^2 is the squared length of vector r. Since |r|^2 is constant for all points, we can omit it from the distance computation without changing result:
d^2 = |r⨯(p-s)|^2
Compare the approximated square distances and keep the minimum. The advantage of this formula is that you can do everything with integers since you mentioned that all coordinates are integers.
I'm afraid you can't get away with computing less than 6 distances (if you could, at least one point would be left out -- including the nearest one).
See if it makes sense to preprocess: Is the line fixed and the points vary? Consider rotating coordinates to make the line horizontal.
As there are few points, it is doubtful that this is your bottleneck. Measure where the hot spots are, redesign algorithms/data representation, spice up compiler optimization, compile to assembly and bum that. Strictly in that order.
Jon Bentley's "Writing Efficient Programs" (sadly long out of print) and "Programming Pearls" (2nd edition) are full of advise on practical programming.
So, I have two points, say A and B, each one has a known (x, y) coordinate and a speed vector in the same coordinate system. I want to write a function to generate a set of arcs (radius and angle) that lead A to status B.
The angle difference is known, since I can get it by subtracting speed unit vector. Say I move a certain distance with (radius=r, angle=theta) then I got into the exact same situation. Does it have a unique solution? I only need one solution, or even an approximation.
Of course I can solve it by giving a certain circle and a line(radius=infine), but that's not what I want to do. I think there's a library that has a function for this, since it's quite a common approach.
A biarc is a smooth curve consisting of two circular arcs. Given two points with tangents, it is almost always possible to construct a biarc passing through them (with correct tangents).
This is a very basic routine in geometric modelling, and it is indispensable for smoothly approximating an arbirtrary curve (bezier, NURBS, etc) with arcs. Approximation with arcs and lines is heavily used in CAM, because modellers use NURBS without a problem, but machine controllers usually understand only lines and arcs. So I strongly suggest reading on this topic.
In particular, here is a great article on biarcs on biarcs, I seriously advice reading it. It even contains some working code, and an interactive demo.
I'm looking for interpolating some contour lines to generating a 3D view. The contours are not stored in a picture, coordinates of each point of the contour are simply stored in a std::vector.
for convex contours :
, it seems (I didn't check by myself) that the height can be easily calculates (linear interpolation) by using the distance between the two closest points of the two closest contours.
my contours are not necessarily convex :
, so it's more tricky... actualy I don't have any idea what kind of algorithm I can use.
UPDATE : 26 Nov. 2013
I finished to write a Discrete Laplace example :
you can get the code here
What you have is basically the classical Dirichlet problem:
Given the values of a function on the boundary of a region of space, assign values to the function in the interior of the region so that it satisfies a specific equation (such as Laplace's equation, which essentially requires the function to have no arbitrary "bumps") everywhere in the interior.
There are many ways to calculate approximate solutions to the Dirichlet problem. A simple approach, which should be well suited to your problem, is to start by discretizing the system; that is, you take a finite grid of height values, assign fixed values to those points that lie on a contour line, and then solve a discretized version of Laplace's equation for the remaining points.
Now, what Laplace's equation actually specifies, in plain terms, is that every point should have a value equal to the average of its neighbors. In the mathematical formulation of the equation, we require this to hold true in the limit as the radius of the neighborhood tends towards zero, but since we're actually working on a finite lattice, we just need to pick a suitable fixed neighborhood. A few reasonable choices of neighborhoods include:
the four orthogonally adjacent points surrounding the center point (a.k.a. the von Neumann neighborhood),
the eight orthogonally and diagonally adjacent grid points (a.k.a. the Moore neigborhood), or
the eight orthogonally and diagonally adjacent grid points, weighted so that the orthogonally adjacent points are counted twice (essentially the sum or average of the above two choices).
(Out of the choices above, the last one generally produces the nicest results, since it most closely approximates a Gaussian kernel, but the first two are often almost as good, and may be faster to calculate.)
Once you've picked a neighborhood and defined the fixed boundary points, it's time to compute the solution. For this, you basically have two choices:
Define a system of linear equations, one per each (unconstrained) grid point, stating that the value at each point is the average of its neighbors, and solve it. This is generally the most efficient approach, if you have access to a good sparse linear system solver, but writing one from scratch may be challenging.
Use an iterative method, where you first assign an arbitrary initial guess to each unconstrained grid point (e.g. using linear interpolation, as you suggest) and then loop over the grid, replacing the value at each point with the average of its neighbors. Then keep repeating this until the values stop changing (much).
You can generate the Constrained Delaunay Triangulation of the vertices and line segments describing the contours, then use the height defined at each vertex as a Z coordinate.
The resulting triangulation can then be rendered like any other triangle soup.
Despite the name, you can use TetGen to generate the triangulations, though it takes a bit of work to set up.
I have some discrete values and assumption, that these values lie on a Gaussian curve.
There should be an algorithm for max-calculation using only 3 discrete values.
Do you know any library or code in C/C++ implementing this calculation?
Thank you!
P.S.:
The original task is auto-focus implementation. I move a (microscope) camera and capture the pictures in different positions. The position having most different colors should have best focus.
EDIT
This was long time ago :-(
I'just wanted to remove this question, but left it respecting the good answer.
You have three points that are supposed to be on a Gaussian curve; this means that they lie on the function:
If you take the logarithm of this function, you get:
which is just a simple 2nd grade polynomial, i.e. a parabola with a vertical axis of simmetry:
with
So, if you know the three coefficients of the parabola, you can derive the parameters of the Gaussian curve; incidentally, the only parameter of the Gaussian function that is of some interest to you is b, since it tells you where the center of the distribution, i.e. where is its maximum. It's immediate to find out that
All that remains to do is to fit the parabola (with the "original" x and the logarithm of your values). Now, if you had more points, a polynomial fit would be involved, but, since you have just three points, the situation is really simple: there's one and only one parabola that goes through three points.
You now just have to write the equation of the parabola for each of your points and solve the system:
(with , where the zs are the actual values read at the corresponding x)
This can be solved by hand (with some time), with some CAS or... looking on StackOverflow :) ; the solution thus is:
So using these last equations (remember: the ys are the logarithm of your "real" values) and the other relations you can easily write a simple algebraic formula to get the parameter b of your Gaussian curve, i.e. its maximum.
(I may have done some mess in the calculations, double-check them before using the results, anyhow the procedure should be correct)
(thanks at http://www.codecogs.com/latex/eqneditor.php for the LaTeX equations)
I need to find for each point of the data set all its nearest neighbors. The data set contains approx. 10 million 2D points. The data are close to the grid, but do not form a precise grid...
This option excludes (in my opinion) the use of KD Trees, where the basic assumption is no points have same x coordinate and y coordinate.
I need a fast algorithm O(n) or better (but not too difficult for implementation :-)) ) to solve this problem ... Due to the fact that boost is not standardized, I do not want to use it ...
Thanks for your answers or code samples...
I would do the following:
Create a larger grid on top of the points.
Go through the points linearly, and for each one of them, figure out which large "cell" it belongs to (and add the points to a list associated with that cell).
(This can be done in constant time for each point, just do an integer division of the coordinates of the points.)
Now go through the points linearly again. To find the 10 nearest neighbors you only need to look at the points in the adjacent, larger, cells.
Since your points are fairly evenly scattered, you can do this in time proportional to the number of points in each (large) cell.
Here is an (ugly) pic describing the situation:
The cells must be large enough for (the center) and the adjacent cells to contain the closest 10 points, but small enough to speed up the computation. You could see it as a "hash-function" where you'll find the closest points in the same bucket.
(Note that strictly speaking it's not O(n) but by tweaking the size of the larger cells, you should get close enough. :-)
I have used a library called ANN (Approximate Nearest Neighbour) with great success. It does use a Kd-tree approach, although there was more than one algorithm to try. I used it for point location on a triangulated surface. You might have some luck with it. It is minimal and was easy to include in my library just by dropping in its source.
Good luck with this interesting task!